Discovering Plumbing Basics is Important When Installing a Bathtub
Discovering Plumbing Basics is Important When Installing a Bathtub
Blog Article
On this page in the next paragraph you can find some quality advice when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a bath tub isn't specifically brain surgery, however it does need strong plumbing, woodworking, and often, tiling abilities. Changing an old tub with a brand-new one is also a reasonably tough project. If the old bathtub is readily accessible, the project can relocate immediately; if you have to open up a wall to get rid of the old bathtub as well as position the brand-new bath tub, the job is much harder. In either case, the project is within a home handyman's skills, although you will certainly need a helper to leave the old bathtub as well as embeded in the new one. Make sure you have qualified yourself for the job and also fit attempting it. Rather than working with a specialist to take control of a halfway-completed project, it is much better to think about utilizing one prior to you begin. Possibilities are you might need a professional plumber to make tube links.
This short article will assist you mount a brand-new bathtub in your washroom if you have actually already purchased a brand-new tub and don't require to change the setup of your previous water system pipelines.
Your devices as well as material list should consist of the following:
Preparing for the Setup
First of all, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to make sure that if the faucet comes with a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets device to stop stress on the bath tub.
Fit the adaptable tap connectors to the bottom of the two taps making use of 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to now be ready to be suited its last position.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any water remaining in the system. The process of removing the existing faucets can be quite problematic because of the limited accessibility that is usually the case.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Before carrying on to fit the brand-new faucets, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Utilizing the two wood boards under its feet, put the bath tub in the required position. The wooden boards are helpful in evenly spreading the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four small factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the tub until the level checks out degree.
To install faucets, fit all-time low of the furthest adaptable tap adapter to the ideal supply pipe by making a compression sign up with; after that do the same for the other faucet.
Turn on the water and check all joints and new pipework for leaks and also tighten them if required. Load the tub and likewise examine the overflow electrical outlet and the regular electrical outlet for leakages.
Lastly, fix the bath paneling as described in the maker's user's manual. Tiling and also securing around the bath tub should wait until the tub has actually been made use of at the very least once as this will certainly settle it right into its final position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and the other end provides a link to the existent supply pipes.
If you require to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin guaranteeing that the washers remain in location between the faucet as well as the sink. Secure the tap in place with the manufacturer supplied backnut. When the tap is securely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The previous type ought to be connected to the tap finishes first, tightening only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the location where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to crack a rigid seal, creating the water to penetrate the wall in between the bathroom and the tiling, bring about issues with moisture and possible leaks to the ceiling below.
You can choose from a range of coloured sealers to blend in your fixtures and installations. They are offered in tubes and also cartridges, as well as are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill up the tub with water before securing, to allow for the activity experienced when the tub is in usage. The sealer can fracture fairly early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently readily available on the marketplace. It is recommended to fit the ceramic tiles utilizing waterproof or waterproof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that article about A Step-by-Step Guide to Installing a Bathtub through a friend on another web blog. Do you know about somebody else who is truly interested in the niche? Why not share it. Thank you so much for taking the time to read it.
Instant help? Contact. Report this page